Microstructural characteristics of as-forged and β-air-cooled Zr–2.5Nb alloy

Multiple characterization and analysis techniques including electron backscatter diffraction (EBSD), electron channeling contrast (ECC) imaging, transmission electron microscopy (TEM) and microhardness test were jointly employed to investigate microstructural characteristics such as local composition, morphology, grain boundary characteristics and interphase orientation relationship of a forged Zr–2.5Nb alloy before and after β-air-cooling. Results show that the as-forged specimen is composed of equiaxed and lamellar α grains and continuous net-like β-Zr films. After the β-air-cooling, the microstructure of the specimen is featured by basket-weave Widmanstätten structure, in which the inter-α-plate second phases are nanoscale β-Zr. Analyses for crystallographic orientations reveal that the Burgers relationship has been strictly followed during the β→α cooling. Compared to the as-forged specimen, the hardness of the β-air-cooled specimen is higher, which could be attributed to the decreased structural sizes of both α and β phases, and the increased fraction of high angle boundaries as well.     

A low power and low phase-noise 91~96 GHz VCO in 90 nm CMOS

This paper reports a 94 GHz CMOS voltage-controlled oscillator (VCO) using both the negative capacitance (NC) technique and series-peaking output power and phase noise (PN) enhancement technique. NC is achieved by adding two variable LC networks to the source nodes of the active circuit of the VCO. NMOSFET varicaps are adopted as the required capacitors of the LC networks. In comparison with the conventional one, the proposed active circuit substantially decreases the input capacitance (C_in) to zero or even a negative value. This leads to operation (or oscillation) frequency (OF) increase and tuning range (TR) enhancement of the VCO. The VCO dissipates 8.3 mW at 1 V supply. The measured TR of the VCO is 91~96 GHz, close to the simulated (92.1~96.7 GHz) and the calculated one (92.2~98.2 GHz). In addition, at 1 MHz offset from 95.16 GHz, the VCO attains an excellent PN of – 98.3 dBc/Hz. This leads to a figure-of-merit (FOM) of ?188.5 dBc/Hz, a remarkable result for a V- or W-band CMOS VCO. The chip size of the VCO is 0.75 × 0.42 mm², i.e. 0.315 mm².     

LTE室分高倒流小区解决方案的研究

LTE室分高倒流直接影响室内4G用户的感知，同时较大程度拉低LTE网络驻留率指标。由于室内无线环境的封闭性，室分小区之间的覆盖独立性，仅仅通过参数调整的手段达到降低高倒流的效果非常不明显，因此本文针对目前影响室内用户感知的高倒流问题，从高倒流小区的标准出发，对室分高倒流小区的发现手段，产生原因及解决方案进行详尽地阐述，并针对各类型的高倒流情形提出解决方法，最终提供读者发现、分析及解决室分高倒流小区的有效方案，从而作为研究方法提供给LTE室内小区高倒流问题解决的指导意见     

风速时间序列混沌判定方法比较研究

混沌识别是对非线性时间序列进行混沌预测的前提。针对时间序列风速确定性与随机性相结合的复杂非线性特征,研究了不同的混沌识别方法,并对风速时间序列进行混沌特征识别。应用随机噪声、周期运动及经典混沌系统的时间序列对所选方法进行可靠性验证。对美国国家风能研究中心M2测风塔实测时间序列风速数据进行非线性混沌特征识别。结果表明:风速时间序列具有明显的混沌特征;各风速时间序列表现出不同程度的混沌特征;各混沌识别方法对风速时间序列混沌特征的表达形式不同,互为补充,相互验证。     

Computing approximate blocking probabilities for transparent waveband switching based WDM networks using hierarchical cross-connects

An analytical model is presented to study the dynamics of wavelength division multiplexing (WDM) networks with waveband switching (WBS). The reduced load approximation method is considered to compute approximated network blocking probabilities in WBS-based WDM networks. The analytical model considers the link blocking probability due to insufficient link capacity and an impact of the waveband granularity (G). The analytical model also considers the node blocking probability due to unavailability of a switch port at the wavelength cross connect (WXC) layer of an Hierarchical cross connect (HXC) switch node. The set of nonlinear equations is obtained with the link independence assumption and solved using repeated substitutions. The accuracy of the analytical model is examined by comparing with simulation results considering the random-fit algorithm for waveband and wavelength assignments in different network scenarios. Lightpaths are routed between source and destination (s-d) HXC switch nodes using shortest path first (SPF) routing. An impact of the switch parameter to limit the input and the output WXC switch ports of an HXC switching node is also being investigated using the analytical model as well as through simulation results.     

Cobalt ferrite nanoparticles prepared by microwave hydrothermal synthesis and adsorption efficiency for organic dyes: Isotherms,thermodynamics and kinetic studies

Magnetic nanoferrites (MFe₂O₄, M = Co, Ni) were successfully synthesised through microwave-hydrothermal route, characterised and used for adsorption of Eriochrome Black T (EBT) and Bromophenol Blue (BRB) dyes from their aqueous solution. The powder XRD patterns confirmed the formation of cubic spinel structure for both the ferrites. Under identical conditions, the adsorption efficiency of CoFe₂O₄ was found relatively higher than the corresponding NiFe₂O_4. Further characterisations revealed that CoFe₂O₄ sample was nearly spherical in size (8–9 nm) with narrow size distribution. The sample showed superparamagnetic behaviour with saturation magnetization (M_s) value (66.4 emu/g). BET surface area calculated for the synthesized cobalt ferrite as 70.9 m²/g. Batch adsorption experiments as a function of initial dye concentration, pH, contact time and adsorbent dose showed the adsorption of dyes depends on pH. Equilibrium adsorption data were well explained by both Langmuir and Freundlich isotherm models. The maximum monolayer adsorption capacities (Q_o) were found to be 82.6 and 25.6 mg/g for EBT and BRB dyes, respectively. Kinetics of the adsorption was best described by pseudo-second-order model. Various thermodynamic parameters such as ΔG, ΔH and ΔS derived from adsorption data over the temperature range 20–50 °C, accounted for a favourable, spontaneous, endothermic physisorption process. The materials showed potential for repeated use without significant decrease in adsorption capacity after proper regeneration.     

改型Wollaston棱镜干涉光谱仪的调制度研究

改型Wollaston棱镜(MWP)无需中继,可构建微型傅里叶变换光谱仪。回顾了MWP的基本原理,从调制度定义出发,计算得到准单色光源的复相干度,找到调制度的影响因素——扩展视场、剪切结构、焦面探测等。建立一般的干涉定域分析模型后,由像点逆光路追迹给出MWP的厚度计算公式,代入调制度约束参数得到不同参量的误差容限。通过FRED记录不同视场扩展情况的灰度与辐照度,结果显示,调制度为0.9时,视场与理论估算值1.24°基本相符;不同剪切量的灰度与辐照度变化特性表明,结构角会使定域垂直系统光轴的入射角发生变化,与晶轴倾角共同影响双折射率差;2.5和8μm像元探测采样表现出调制度差异,描述了定域深度或离焦的影响。以准单色光源、复相干度表示调制度,可将不同影响因素统一至约束参数中,相关变量误差容限可作为MWP-FTS的设计依据。     

Developing microencapsulated 12‐hydroxystearic acid (HSA) for phase change material use

Phase change materials (PCM) have an increasingly more important role as a thermal energy storage (TES) media. However, leakage problem of PCM causes limitation during their integration in TES systems. Therefore, the encapsulation of PCMs is attracting research interest to extend usage of PCMs in real TES applications in recent years. In this study, hydroxystearic acid (HSA) was encapsulated with polymethyl methacrylate (PMMA) and different PMMA comonomer shells via emulsion polymerization method for the first time in literature. HSA with high melting temperature range (74–78°C) can widen the scope of using PCMs, and the encapsulated form can make it more versatile. The chemical structures, morphologies, and thermophysical properties of capsules were determined by FT‐IR, SEM, DSC, TGA, and thermal infrared camera. Among the produced HSA capsule candidates, PMMA‐HEMA is the most promising with latent heat of 48.5 J/g with melting range of 47 to 85°C. SEM analysis indicated that the capsules have spherical shape with compact surface at nano‐micro (100–440 nm) size range; however, some capsules exhibited agglomeration.     

β-环糊精修饰Ni/SFCC强化C9石油树脂催化加氢性能

以废弃的流化催化裂化催化剂（简称SFCC）为载体、β-环糊精为金属络合剂、硝酸镍为镍源，采用湿法浸渍法制备β-环糊精修饰的Ni/SFCC催化剂（简称Ni/SFCC-CD催化剂），考察其对C9石油树脂的催化加氢性能。通过BET比表面积测试、H2程序升温还原、X射线光电子能谱等手段对催化剂的物相结构进行表征，研究β-环糊精的作用机理及其对催化剂加氢性能的影响。研究结果表明：在反应温度为260 ℃、反应压力为7 MPa、反应时间为2.0 h的最优条件下，采用Ni/SFCC-CD催化C9石油树脂加氢，可制得溴值为1.45 gBr/（100 g）、色号（加纳德）小于1的水白色氢化C9石油树脂，催化剂循环使用4次后仍保持良好活性；β-环糊精的作用机理是：β-环糊精与硝酸镍产生络合作用，抑制硝酸镍的分解、控制NiO的结晶过程和增强活性组分Ni与载体之间的相互作用力，从而提高了Ni/SFCC-CD的催化活性和稳定性。